WILKERSON INSTRUMENT CO., INC.

LM1000-PM Level Monitor and Control
Panel Mount

Wici Logo
Home Button Wilkerson Instrument Co.    800-234-1343 Wilkerson Instrument Co Blog PageWilkerson Instrument Co LinkedIn PageShopping Cart

DR4380AUR/cUR Logo

LM1000-PM
Level Monitor
and Control
Panel Mount

$625.00

The following information must be entered to complete your order:
See "Specifications" below for Input range limits.

Input:
(Select the Appropriate Range for Your Application)
Alarm Action

 

 

Quantity:

 

Don't Forget Your Accessories

LS1000 Level Sensor

 
  • Features
  • Description
  • Specifications
  • Connections
  • Available in panel mount and NEMA 4X enclosed versions.
  • Bright 4 digit LED Display indicates level in feet to two decimal places
  • Built in level sensor calibrator
  • Relay output that can be used for alarm or control output.
  • Setpoint adjustable over entire 4-20 mA span
  • Dead band adjustable 1% to 90%
  • Built in 24 VDC 2 wire sensor transmitter power supply
  • UL /cUL Recognized

The LM1000 is designed to monitor the level of liquids using a pressure sensor as the source of level data. A four digit LED display indicates level in feet to two decimal places (XX.XX). The LM1000 provides 24 VDC regulated power for a two wire transmitter.
An Alarm circuit with a SPDT relay output can be set as a high or low alarm. It can be configured as a Normal or Reverse Acting (fail safe) alarm. The Setpoint control is adjustable over the entire 4-20 mA input range and a Deadband control allows the Hysteresis to be set from less than 1% to 90% of the span.

Using the Alarm circuit, the LM1000 can also be used as a level control by setting the Alarm to trip at a high level to start the pump and setting the Deadband to stop the pump when the level falls to the desired lower limit.

The LED display can be switched to indicate level or to accurately indicate the loop 4-20 mA current. A built in calibrator allows the loop current to be adjusted over the 4-20 mA range with a ten turn potentiometer. The calibrator function is chosen with a spring loaded switch that returns the LM1000 to the Level indication mode when released. This spring loaded switch insures the unit is not inadvertently left in the Calibration mode. The unique positioning of the switch in relationship to the adjustment potentiometer allows single handed simultaneous operation of both the switch and the potentiometer.

The calibration function can be used to calibrate the LED display in Level. It can also be used to calibrate the alarm Setpoint and Deadband. An LED indicator behind the display lens indicates when the alarm is energized.

The panel mount version is designed to replace bubbler level monitors and is an exact fit for several bubbler products.

INPUT
2 wire transmitter output proportional to level
(LM1000 provides 24 VDC power to transmitter)

DISPLAY
4 Digit .56” LED

DISPLAY RESOLUTION
2 decimal places to 99.99 Ft. or loop current in mADC

OUTPUT
4/20 mADC proportional to Level

ALARM / CONTROL OUTPUT
SPDT Relay rated 5 Amps, 240 VAC

DEADBAND
Adjustable 1% to 90% of scale

CONTROL TYPE
On - Off
Reverse (pump out) or Direct (pump in)

POWER
120 VAC +10%, 50/60 Hz 3.5 VA maximum

ACCURACY
0.05% of Span + 1 digit

OPERATING TEMPERATURE
-13°F to 176°F (-25°C to 80°C)

ENCLOSURE
Panel Mount
Anodized aluminum front panel
Dimensions: 6.13” x 7.75” x 1.88”

TERMINAL MARKING

Output +
Output -
Sensor +
Sensor -
Shld
N/C
N/C
Alarm Relay NC
Alarm Relay NO
Alarm Relay COM
N/C
Power Gnd
Power L1
Power L2

DESCRIPTION

4-20 mA + Output
4-20 mA - Output
Two Wire Transmitter +
Two Wire transmitter -
Shield
No Connection
No Connection
Normally Closed Contact
Normally Open Contact
Relay Common
No Connection
Connection to LM1000 Metal Chassis
AC Power Line 1
AC Power Line 2

Specifications    Manual

Solutions Provider for Signal Conditioning and
Process Control Instrumentation